検索結果 1436 件
| JaLCDOI | 10.18926/15787 |
|---|---|
| フルテキストURL | Mem_Sch_Eng_OU_19_1_45.pdf |
| 著者 | Oda Kiichi| Yoshio Tetsuo| O-oka Kazuo| |
| 抄録 | Succeeding to 60(Ba,Sr)TiO(3)-10A1(2)O(3)-30SiO(2)glassceramics reported in our previous paper, another type
of ferroelectric glass-ceramics was elaborated by the
controlled growth of Ba(l-x)Ca(x)TiO(3) crystal particles in the glass system 60 (Ba(l-y)Ca(y)) TiO(3)-10Al(2)O(3)-30SiO(2) (0.0 |
| 出版物タイトル | Memoirs of the School of Engineering, Okayama University |
| 発行日 | 1984-11-26 |
| 巻 | 19巻 |
| 号 | 1号 |
| 開始ページ | 45 |
| 終了ページ | 51 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307972 |
| JaLCDOI | 10.18926/15721 |
|---|---|
| フルテキストURL | Mem_Sch_Eng_OU_12_53.pdf |
| 著者 | Fujitsuka Takeshi| Agusa Toru| |
| 抄録 | In recent years, the development of a high power transistor element is proceeding. A high power inverter circuit using power transistors are finding a good number of applications in induction heating and melting. Turn off time of power transistors occupies 5-lOμs of switching characteristics. A driving method to give base inputs for a half period is widely used for a inverter circuit. But this method has the following defects, the short-circuit current flows through two transistors because the other pair transistors turn on before one pair transistors turn off. So the switching loss is increased, the maximum output and the efficiency are decreased. In this paper, a driving method to give base inputs for the less period as compared with a half period is discussed. Using this method, the foregoing defects is lost and the driving frequency is able to become higher. In addition, it become clear that the square waveform output is given using this method in the case of R-L load. |
| 出版物タイトル | Memoirs of the School of Engineering, Okayama University |
| 発行日 | 1978-02-25 |
| 巻 | 12巻 |
| 開始ページ | 53 |
| 終了ページ | 58 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307552 |
| JaLCDOI | 10.18926/15700 |
|---|---|
| フルテキストURL | Mem_Sch_Eng_OU_13_45.pdf |
| 著者 | Fujitsuka Takeshi| Agusa Toru| |
| 抄録 | In this paper, the steady state operations of the squarewave inverter circuit with a series R-L load are discussed. The circuit consists of transistors and feedback diodes. The basic equation is derived from its equivalent circuit. Solving the basic equation with steady state conditions, the instaneous value of the load current i is derived. The period t(2) for which the current flows from the supply to the load and the period t(l) for which the current feedbacks through diodes from the load to the supply are calculated from (i), and the ratio of t(l) to t(2) is illustrated using power factor of fundamental wave, pf, as a variable. The ratios of transistor mean current I(tr), diode mean current I(D), supply mean current I(s) to the load current I are illustrated using pf as a variable, too. In result, each current ratios to I is shown in simple expressione. The load current can be calculated simply using the coefficient reading off the figure. In addition, it becomes clear from the figure that the load current is scarcely influenced by the harmonic voltage in less than 0.8 of pf. The ratio t(2)/(t(1)+t(2)) calculated in squarewave voltage, shows the limit of pulse width control whose out put voltage is the squarewave. |
| 出版物タイトル | Memoirs of the School of Engineering, Okayama University |
| 発行日 | 1979-03-05 |
| 巻 | 13巻 |
| 開始ページ | 45 |
| 終了ページ | 52 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307473 |
| JaLCDOI | 10.18926/15639 |
|---|---|
| フルテキストURL | Mem_Sch_Eng_OU_6_47.pdf |
| 著者 | Takahashi Katsuaki| Goto Yasumasa| |
| 抄録 | The glass forming limit by substitution of CdS for CdO in a CdO-B(2)0(3) glass was determined by chemical analysis. When x CdS-(60-x)CdO-40B(2)0(3) nominal mixtures in weight ratio were heated at 1100°C in flowing nitrogen gas for 1/2 hour, about 40~50% of mixed CdS and 10-15% of the mixed CdS were evaporated. The limit of nominal composition for glass forming was 10CdS-50CdO-40B(2)0(3) and the corresponding virtual composition after the above heat treatment was found to be 4.9CdS-46.4CdO-48.7B(2)O(3). Further addition of CdS made the melt devitrefied with CdS precipitation. D.C. conductivity measurements revealed that the current density was not linear with respect to the applied voltage, but the resistivity ranged around 10(12)Ω･cm for 4.1CdS-48.8CdO-47.1B(2)O(3) (virtual composition) glass and around 10(11.5)Ω·cm for 4.9CdS-46.4CdO-48.7B(2)O(3) glass. These sulphur containing glasses did not show photoconduction, although CdS-precipitated materials showed slight photoconductivity when disposed in ultra violet radiation. Apparent dielectric constant and tan 8 were also measured as a function of frequency, revealing a moderate dispersion in the CdS-precipitated glasses. |
| 出版物タイトル | Memoirs of the School of Engineering, Okayama University |
| 発行日 | 1971-09-01 |
| 巻 | 6巻 |
| 号 | 1号 |
| 開始ページ | 47 |
| 終了ページ | 52 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307147 |
| JaLCDOI | 10.18926/15630 |
|---|---|
| フルテキストURL | Mem_Sch_Eng_OU_6_7.pdf |
| 著者 | Hirose Koji| Oka Takuma| |
| 抄録 | A series of turbulent pipe flow experiments with dilute aqueous C.M.C. solutions are described. The purpose of these experiments are to compare the anomalous viscous drag results from these experiments with the results using water (Newtonian viscous fluid). The additive concentrations of the present experiments are from 0.01% to 0.5% by weight of C.M.C., giving power-law indexes 1 to 0.75, respectively. All of the concentrations are found to give a reduction in turbulent friction factor, compared with Newtonian at the same Reynolds number. A maximum friction factor reduction of 64 % is obtained at a Reynolds number 2x10(3) for solutions having polymer concentration of 0.3% by weight. |
| 出版物タイトル | Memoirs of the School of Engineering, Okayama University |
| 発行日 | 1971-09-01 |
| 巻 | 6巻 |
| 号 | 1号 |
| 開始ページ | 7 |
| 終了ページ | 12 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307497 |
| JaLCDOI | 10.18926/15625 |
|---|---|
| フルテキストURL | Mem_Sch_Eng_OU_3_77.pdf |
| 著者 | Monobe Kazuo| Yamashita Yuhiko| Fujiwara Yasuo| Fujiwara Yoshitaka| |
| 抄録 | We tried to clarify the crystallization mechanism of long chain polymers in solution under shearing stress using polyethylene. From the bright and dark field electron microscope observations and the electron diffraction study, we demonstrated that the resulting fibrous crystals consist of the central threads with an extended chain character and the lamellae with a folded chain character nucleated on the threads. The measurements of thermal and mechanical properties gave the additional confirmation for this suggestion. From these results we discussed the crystallization mechanism on the fibrous crystals. |
| 出版物タイトル | Memoirs of the School of Engineering, Okayama University |
| 発行日 | 1968-09-01 |
| 巻 | 3巻 |
| 号 | 1号 |
| 開始ページ | 77 |
| 終了ページ | 83 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307234 |
| JaLCDOI | 10.18926/15624 |
|---|---|
| フルテキストURL | Mem_Sch_Eng_OU_3_157.pdf |
| 著者 | Misaki Takayoshi| Okamoto Takuji| Kato Osamu| |
| 抄録 | In the analog circuits for the systms governed by the dilfercntial equations with the coefficients which are a function of one or mOre of the dependent variables, the magnitudes of their circuit elements must be variable in accordance with the nature of the function. Such circuit elements can be realized by means of inserting or removing the additional elements with high speed switches in the analog circuits. Particularly, in the case of varying stepwise this method is effective. But as an analog circuit is regarded as a short-time or repetitive type analyzer, the above switches must be instantaneous operation. In this paper, first, it is made sure by the experiments that some of the transistor switches arc met this condition, and moreover arc very low closed resistance, very high open resistance and neglegible small voltage offsets. Next, the basic technique for the direct analog simulation usiug transistor switches is described about the simple example, i.e. the oscillatory system with varying cross-scctional surge tank. Finally, as its applications, the transient problems of these oscillatory systems arc solved by means of these analog circuits. |
| 出版物タイトル | Memoirs of the School of Engineering, Okayama University |
| 発行日 | 1968-09-01 |
| 巻 | 3巻 |
| 号 | 1号 |
| 開始ページ | 157 |
| 終了ページ | 162 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307953 |
| JaLCDOI | 10.18926/15595 |
|---|---|
| タイトル（別表記） | BALNEOLOGICAL STUDIES USING RADIOACTIVE ISOTTPES (2) INFLUENCE OF THE PHYSICOCHEMICAL PROPERTIES OF BATH WATER UPON THE TRANSITION OF SULFATE ION INTO THE BODY ACROSS THE SKIN. |
| フルテキストURL | 008_008_012.pdf |
| 著者 | 横田 剛男| |
| 抄録 | Using Na(2)SO(4) labeled with S(85) transition of sulfate ion into the body across the skin was investigated soon after the bath in sodium sulfate solution(one gram per liter) at varying conditions. Mice were used as test animal. Percutaneous absorption of sulfate ion was promoted at indifferent bath temperature (37℃) than at lower bath temperature (25℃), became less by the addition of sodium chloride (one gram per liter) to the bath water, proved stronger at lower pH (2.0) than at higher pH (7.0 or 9.0). One of the characteristic types of mineral waters in Japan is "acid spring". And many of the Japanese acid springs contain free sulfuric acid in considerable quantity.It is known that their bath cure often causes dermatitis, socalled "Yutadare". Misawa and Oshima had proved that the level of immune bodies in blood is increased by the bath cure with dermatitis in acid springs of "KUSATSU". And the author's experiment seems to give a new significance to the ro1e of sulfate ion in the action of acid spring bath in Japan. |
| 出版物タイトル | 岡山大学温泉研究所報告 |
| 発行日 | 1952-11 |
| 巻 | 8巻 |
| 開始ページ | 8 |
| 終了ページ | 12 |
| ISSN | 0369-7142 |
| 関連URL | http://eprints.lib.okayama-u.ac.jp/15355 |
| 言語 | 日本語 |
| 論文のバージョン | publisher |
| NAID | 120002307410 |
| JaLCDOI | 10.18926/15551 |
|---|---|
| フルテキストURL | Mem_Sch_Eng_OU_1_84.pdf |
| 著者 | Misaki Takayoshi| Kato Osamu| |
| 抄録 | Described in this paper are the design considerations of the simple element of the two-dimensional RC distributed constant circuit and its applications for the analysis of the transient heat conduction problems in engineering work. This element is formed by coating with the resistive film the upper surface of the high permittivity ceramics plate whose back side to be silvered. In addition to a resistivity of every elementary area within the resistive film, there exists capacitive coupling between the area and ground. This element can be regarded as a typical two-dimensional RC distributed system and utilized as a simulator for the same dimensional heat conduction system. It has a convenience and high accuracy for the analysis of the transient heat conduction problems in engineering work. |
| 出版物タイトル | Memoirs of the School of Engineering, Okayama University |
| 発行日 | 1966-03-31 |
| 巻 | 1巻 |
| 号 | 1号 |
| 開始ページ | 84 |
| 終了ページ | 90 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307680 |
| JaLCDOI | 10.18926/15466 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_24_1_1.pdf |
| 著者 | 吉田 彰| 大上 祐司| 藤井 正浩| |
| 抄録 | To clarify the effects of a drive system lubricant additive upon rolling fatigue of rollers manufactured from carburized and hardened steel, three types of oil were used as lubricants: one mineral base oil and the other two mineral base oils to which an S-P additive package and ATF additive package were added, respectively. These specimens were tested for sliding/rolling fatigue and examined for failure on the surface, rolling fatigue strength, and other properties. Roller surface temperatures and inter-roller frictional coefficients were found scarcely affected by the type of oil used. Irrespective of the difference in oil type, failure on the surface was found to be entirely spalling attributable to cracks generated in the subsurface. The depth at which spalling cracks had taken place was found nearly coincident with the depth at which a ratio of reversing orthogonal shear stress to hardness had amplitude A(Tyz/Hv) maximized. These depths were larger as Hertz stress became more prominent. Nevertheless, they were found hardly affected by the type of oil. Although rolling fatigue strength did not show a significant difference dependent upon the type of oil, it may be said that fatigue life would be somewhat negatively affected by an extreme pressure coated film with a content of sulfur and phosphorus. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 1989-11-29 |
| 巻 | 24巻 |
| 号 | 1号 |
| 開始ページ | 1 |
| 終了ページ | 12 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307588 |
| JaLCDOI | 10.18926/15408 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_29_2_1.pdf |
| 著者 | 榊原 精| Nakagawa, Keiyu| Kanadani, Teruto| |
| 抄録 | Effect of addition of a small amount of copper to Al- 12mass % Zn binary alloy on the process of low temperature aging is studied by hardness test and transmission electron microscopy. Age hardening rate after quenching from various temperatures is slowed down by addition of 0.5mass % copper to the binary alloy. The hardness obtained after long aging, however, is increased a little by the addition of copper. The extent of soft surface layer formed by aging in the copper-added alloy is nearly equal to that obtained in the binary alloy. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 1995-03-27 |
| 巻 | 29巻 |
| 号 | 2号 |
| 開始ページ | 1 |
| 終了ページ | 4 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307763 |
| JaLCDOI | 10.18926/15375 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_35_177.pdf |
| 著者 | Kanki Kunihiko| 大崎 紘一| 梶原 康博| 宗澤 良臣| Ohta Kazuharu| |
| 抄録 | The focus of this paper is on the analysis of delivery motion of human, development of an image processing method based on the motion analysis and development of the cooperative delivery robot using the image processing method. The proposed image processing method uses two cameras, and it uses a stereo reconstruction technique for measuring position and postures of hands. In addition, this image processing method recognize the number of fingers extending consciously, so the cooperative human beings could choose the kind of tool which he wants by holding out his hand in front of cameras. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2001-03-27 |
| 巻 | 35巻 |
| 号 | 1-2号 |
| 開始ページ | 177 |
| 終了ページ | 182 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307899 |
| JaLCDOI | 10.18926/15371 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_35_163.pdf |
| 著者 | Uchiyama Hiromitsu| Miyazaki Satoshi| 大崎 紘一| 梶原 康博| 宗澤 良臣| Matsuki Katsunori| |
| 抄録 | We develop an assembly robot system for assembling the flexible belt-shaped subject. An image processing method is developed to recognize the belt-shaped subject. This method is able to determine the grasping point and grasping angle for piking up a subject by a multiple hands unit. CAD information is used to determine the grasping point. The multiple hands unit is developed, which is able to grasp all grasping points of a subject at a time. In addition, the image processing method is used to judge whether a subject is fastened accurately at right position or not during the assembly. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2001-03-27 |
| 巻 | 35巻 |
| 号 | 1-2号 |
| 開始ページ | 163 |
| 終了ページ | 168 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307229 |
| JaLCDOI | 10.18926/15370 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_27_2_73.pdf |
| 著者 | Kroumov Valeri T.| 井上 昭| 増田 士朗| |
| 抄録 | This report deals with the problem of designing an adaptive observer for estimating unknown periodical disturbances. This is very practical problem because in the area of control of servomechanisms such disturbances are always encountered. When the disturbance cannot be directly measured or eliminated at the source it is necessary to perform a prediction. When a periodical disturbance is present the frequencies appear as unknown parameters and they have to be identified. In order to identify the unknown parameters, it is necessary to transform the composite system model, which contains the models of the controlled system and the disturbances, into observable canonical form. In addition, an inverse transformation is required to calculate the estimates of the present disturbances. In this report, firstly, a review of an adaptive observer for estimation of unknown periodical disturbances is presented. Later a calculation of the disturbance estimate is derived using the algebraic programming system REDUCE. The proposed method here allows to perform all the necessary transformations and to obtain the disturbance estimation without using the transformation matrix. The calculations of these transformations are complicated and, hitherto, there is no simple method to perform them. The results of disturbance estimation are illustrated by two examples. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 1993-03-25 |
| 巻 | 27巻 |
| 号 | 2号 |
| 開始ページ | 73 |
| 終了ページ | 85 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307731 |
| JaLCDOI | 10.18926/15366 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_35_147.pdf |
| 著者 | 山際 雅詩| 酒井 裕| |
| 抄録 | The Cry4A toxin is a dipteran-specific insecticidal protein produced by Bacillus thuringiensis subsp. israelensis as a protoxin of 130 kDa. Its active form is a heterodimer of 20- and 45-kDa fragments which is generated by an interhelical cleavage of a 60-kDa intermediate at the position of Gln236 between α5 and α6 helices in domain I. On the other hand, Cry1Aa, which is also produced as a 130-kDa protoxin but toxic to lepidopteran larvae, was processed into the active 60-kDa fragment with no additional cleavage. To investigate the role of the intramolecular cleavage of Cry4A for its insecticidal activity, the loop between α5 and α6 of Cry4A which includes the cleavage site was substituted for the corresponding region of Cry1Aa. The resulting mutant designated GST-60Loop was expressed as a GST-fusion protein. A difference of the processing profile was observed between GST-60 and GST-60Loop in the in vitro digestion assay by trypsin, and the insecticidal activity of GST-60Loop was two-fold lower than that of GST-60. These results suggested that the interhelical cleavage of Cry4A promoted the toxicity against C. pipiens larvae. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2001-03-27 |
| 巻 | 35巻 |
| 号 | 1-2号 |
| 開始ページ | 147 |
| 終了ページ | 154 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307324 |
| JaLCDOI | 10.18926/15348 |
|---|---|
| フルテキストURL | Mem_Fac_Eng_OU_35_21.pdf |
| 著者 | S.kovalenko, Volodymyr| Uno, Yoshiyuki| Okamoto, Yasuhiro| Anyakin, M.| Lutay, A.| Shubul, Khaled Al.| |
| 抄録 | In electric power industry, there is a problem of achieving stable joint in different components using high productive and efficient technologies. One type of these components is packages of slices for magnetic circuit of electric motors, transformers etc., which need reliable means for their fixing. Laser welding is proposed to solve this problem as an alternative for existing technologies. The development of the laser welding process is presented based on process simulation, study of heat history and comparison with experimental results. Laser beam additional scanning technique is proposed to improve the quality and efficiency of the joining operation. |
| 出版物タイトル | Memoirs of the Faculty of Engineering, Okayama University |
| 発行日 | 2001-03-27 |
| 巻 | 35巻 |
| 号 | 1-2号 |
| 開始ページ | 21 |
| 終了ページ | 28 |
| ISSN | 0475-0071 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| NAID | 120002307424 |
| JaLCDOI | 10.18926/15341 |
|---|---|
| タイトル（別表記） | 抗原および抗ヒトIgEに対する好塩基球の反応性. 2.分泌機序における形態的変化 |
| フルテキストURL | 063_128_133.pdf |
| 著者 | 谷崎 勝朗| 高橋 清| 木村 郁郎| |
| 抄録 | Morphological changes of blood basophils activated by antigen and anti-IgE were discussed in relation to release mechanisms of the cells. 1. Basophils activated by antigen and anti-IgE show two different types : A form (pear-shaped) and B from (swollen type), on smear preparartions. 2. Pear-shaped basophils(reactive basophils), which appear after stimulation by antigen and anti-IgE, can be observed by the staining solution for the direct count of basophils and eosinophils. 3. The incidence of reactive basophils increases after addition of antigen. Thus, observation of reactive basophils can be clinically applied for detecting allergen (DCRB ; direct connt of reactive basophils). 4. Observation of morphological basophil response by phase- contrast microscopic motion pictures demonstrates that basophils activated by antigen show two different reponses, increase in motility (oriented movement) and degranulation. |
| キーワード | morphological changes of basophils (好塩基球の形態的変化) reactive basophils (反応好塩基球) degranulation (脱顆粒) histamine release (ヒスタミン遊離) |
| 出版物タイトル | 岡大三朝分院研究報告 |
| 発行日 | 1992-06 |
| 巻 | 63巻 |
| 開始ページ | 128 |
| 終了ページ | 133 |
| ISSN | 0913-3771 |
| 言語 | 英語 |
| 論文のバージョン | publisher |
| JaLCDOI | 10.18926/15243 |
|---|---|
| タイトル（別表記） | Consideration to the change of swallowing sense after operation of esophagus cancer - Evaluation of swallowing activity by using IPG and swallowing sound - |
| フルテキストURL | 012_1_053_062.pdf |
| 著者 | 森 恵子| 山本 尚武| 中村 隆夫| 楠原 俊昌| |
| 抄録 | 食道癌患者は腫瘍による狭窄のため,程度の差はあるものの,術前より通過障害を認めることが多い｡食道癌と診断され,手術を自己決定した患者の多くは,手術をして罹患前のように食事ができるようになりたいと思っている｡しかし,患者の多くが術後に嚥下感覚の変化に遭遇する｡現在,手術前に実施されるインフォームドコンセント(以下IC)では,術後に起こる嚥下感覚の変化については説明が行われていない｡そのため患者は,経口摂取が可能になった時点で嚥下感覚の変化を自覚し,強い不安を感じる｡今回, 5人の患者に術後の嚥下感覚の変化に関するインタビューを実施するとともに,術後の嚥下活動を頸部電気インピーダンスおよび嚥下音を用いて測定した｡インタビューの結果, 5人全てが,術後に嚥下感覚の変化を自覚し,不安を感じていた｡また,青年健常者と比較し,IPG波形の多相化と,嚥下音の咽頭期以外での発生が認められた｡患者が,術後に起こる嚥下感覚の変化についてのICを望んでいることからも,術後の嚥下感覚の変化についてのICを行なう必要がある｡ |
| キーワード | 食道癌 (esophagus cancer) 嚥下障害 (swallowing disorder) 生体電気インピーダンス (bioelectrical impedance) インフォームドコンセント (informed consent) |
| 出版物タイトル | 岡山大学医学部保健学科紀要 |
| 発行日 | 2001-12-25 |
| 巻 | 12巻 |
| 号 | 1号 |
| 開始ページ | 53 |
| 終了ページ | 62 |
| ISSN | 1345-0948 |
| 言語 | 日本語 |
| 論文のバージョン | publisher |
| NAID | 120002307448 |
| JaLCDOI | 10.18926/15224 |
|---|---|
| タイトル（別表記） | Color environment of maternity centers - Visual measurements of consultation and waiting room areas - |
| フルテキストURL | 013_1_037_045.pdf |
| 著者 | 小野 清美| 奥田 博之| 光岡 美智子| |
| 抄録 | これまで助産所管理に関する事柄において色彩環境についてあまり触れられてこなかったが,色彩環境はよい環境を作りだすことができる要素である｡そこで､M助産院の診察室および玄関兼待合室の色彩環境の視感測定を実施した｡M事例でわかったことは,ソファカバーや観葉植物･造花などの有効な活用を図っていたが,人形やスリッパなどの小物は目立つ色彩であった｡また,大きなポスターは周囲の色彩環境を左右していた｡以上のことから,今後,よい色彩環境にするために留意すべき点は以下の7項目である｡ 1)観葉植物の有意義な活用をすること｡ 2)カーペットやソファーカバーなどで色彩変化を楽しめるが､その素材にも留意すること｡ 3)色彩の散乱を防止し,空間内の色彩秩序を保つこと｡ 4)子どもなどを対象にした物の場合には,対象者の視線にあわせた色彩計画をすること｡ 5)癒しの環境作りに造花は手軽に利用できる｡ 6)大きなポスターを貼る時には､その色彩の影響を考慮し添付場所を選択すること｡ 7)診療場所の色彩は色相より彩度には留意し,｢落ち着き｣｢おだやかさ｣｢ほっとする温かみ｣などを得られるような工夫をすること｡ |
| キーワード | 助産所 (maternity center) 色彩 (color) アメニティ (amenity) |
| 出版物タイトル | 岡山大学医学部保健学科紀要 |
| 発行日 | 2002-12-25 |
| 巻 | 13巻 |
| 号 | 1号 |
| 開始ページ | 37 |
| 終了ページ | 45 |
| ISSN | 1345-0948 |
| 言語 | 日本語 |
| 論文のバージョン | publisher |
| NAID | 120002307475 |
| JaLCDOI | 10.18926/15208 |
|---|---|
| タイトル（別表記） | Provision of information and health care in a maternity ward: More effective use of corridor notice boards |
| フルテキストURL | 014_1_057_064.pdf |
| 著者 | 小野 清美| 奥田 博之| 松井 たみこ| |
| 抄録 | 病棟における情報提供の一つとして掲示板は手軽に利用されるが,これに関する研究はないといっても過言ではない｡しかし,日本医療機能評価機構(Japan Council for Quality Health Care)においては自己評価票の項目として｢掲示物の配慮｣について評価するようになっている｡そこで,O大学附属病院産科病棟の廊下にある掲示板を使用し,掲示板周辺の色彩の視感測定と照度測定を実施し後,掲示物の内容の整理をし,その美観について整理前後の評価をSD法(Semantic Diferenial Method)で評価しその結果, 整理後は好転していた｡さらに,掲示物への意見の調査,希望する掲示内容に関する調査なども実施した｡これらのことから掲示板の有効活用の仕方と情報提供の内容の選別の2点が明確化した｡それぞれの留意点は以下のとおりである｡<有効活用について>1.掲示物の重要度と緊急性に応じた貼り方をする｡2.文字や絵の大きさにより,掲示板の有効活用をする｡<情報提供の内容の選別について>1.産科領域の患者教育および健康教育などの提供の必要性がある｡2.掲示物の内容は患者本人に必要なことか,家族にも必要なことなのか,対象者の明確化をして貼付する必要がある｡3.一般ニュースの提供や絵や写真などの癒しの必要性もある。 |
| キーワード | 情報提供 (information service) サービス (health care) 産科病棟 (maternity ward) |
| 出版物タイトル | 岡山大学医学部保健学科紀要 |
| 発行日 | 2003-12-25 |
| 巻 | 14巻 |
| 号 | 1号 |
| 開始ページ | 57 |
| 終了ページ | 64 |
| ISSN | 1345-0948 |
| 言語 | 日本語 |
| 論文のバージョン | publisher |
| NAID | 120002307962 |