start-ver=1.4 cd-journal=joma no-vol=15 cd-vols= no-issue=11 article-no= start-page=6155 end-page= dt-received= dt-revised= dt-accepted= dt-pub-year=2025 dt-pub=20250530 dt-online= en-article= kn-article= en-subject= kn-subject= en-title= kn-title=Top-Down Stereolithography-Based System for Additive Manufacturing of Zirconia for Dental Applications en-subtitle= kn-subtitle= en-abstract= kn-abstract=This study investigated the feasibility and effectiveness of a commercial top-down stereolithography (SLA)-based system for the additive manufacturing of zirconia dental prostheses. Yttria-stabilized zirconia–resin slurries were prepared, and zirconia objects were fabricated using a top-down SLA system. Thermogravimetric–differential thermal analysis was used to examine the resin, while X-ray fluorescence spectroscopy and X-ray diffraction were used to analyze the printed samples. The microstructures of additively manufactured and subtractively manufactured zirconia were compared using field emission scanning electron microscopy (FE-SEM) before and after sintering. Biaxial flexural strength tests were also conducted to evaluate mechanical properties. The green bodies obtained via additive manufacturing exhibited uniform layering with strong interlayer adhesion. After sintering, the structures were dense with minimal porosity. However, compared to subtractively manufactured zirconia, the additively manufactured specimens showed slightly higher porosity and lower biaxial flexural strength. The results demonstrate the potential of SLA-based additive manufacturing for dental zirconia applications while also highlighting its current mechanical limitations. The study also showed that using a blade to evenly spread viscous slurry layers in a top-down SLA system can effectively reduce oxygen inhibition at the surface and relieve internal stresses during the layer-by-layer printing process, offering a promising direction for clinical adaptation. en-copyright= kn-copyright= en-aut-name=YoshiharaKumiko en-aut-sei=Yoshihara en-aut-mei=Kumiko kn-aut-name= kn-aut-sei= kn-aut-mei= aut-affil-num=1 ORCID= en-aut-name=NagaokaNoriyuki en-aut-sei=Nagaoka en-aut-mei=Noriyuki kn-aut-name= kn-aut-sei= kn-aut-mei= aut-affil-num=2 ORCID= en-aut-name=SpirrettFiona en-aut-sei=Spirrett en-aut-mei=Fiona kn-aut-name= kn-aut-sei= kn-aut-mei= aut-affil-num=3 ORCID= en-aut-name=MaruoYukinori en-aut-sei=Maruo en-aut-mei=Yukinori kn-aut-name= kn-aut-sei= kn-aut-mei= aut-affil-num=4 ORCID= en-aut-name=YoshidaYasuhiro en-aut-sei=Yoshida en-aut-mei=Yasuhiro kn-aut-name= kn-aut-sei= kn-aut-mei= aut-affil-num=5 ORCID= en-aut-name=Van MeerbeekBart en-aut-sei=Van Meerbeek en-aut-mei=Bart kn-aut-name= kn-aut-sei= kn-aut-mei= aut-affil-num=6 ORCID= en-aut-name=KiriharaSoshu en-aut-sei=Kirihara en-aut-mei=Soshu kn-aut-name= kn-aut-sei= kn-aut-mei= aut-affil-num=7 ORCID= affil-num=1 en-affil=National Institute of Advanced Industrial Science and Technology (AIST), Health and Medical Research Institute kn-affil= affil-num=2 en-affil=Advanced Research Center for Oral and Craniofacial Sciences, Okayama University Dental School kn-affil= affil-num=3 en-affil=Joining and Welding Research Institute, Osaka University kn-affil= affil-num=4 en-affil=Department of Prosthodontics, Okayama University kn-affil= affil-num=5 en-affil=Department of Biomaterials and Bioengineering, Faculty of Dental Medicine, Hokkaido University kn-affil= affil-num=6 en-affil=BIOMAT, Department of Oral Health Sciences, KU Leuven kn-affil= affil-num=7 en-affil=Joining and Welding Research Institute, Osaka University kn-affil= en-keyword=additive manufacturing kn-keyword=additive manufacturing en-keyword=subtractive manufacturing kn-keyword=subtractive manufacturing en-keyword=dental prosthesis kn-keyword=dental prosthesis en-keyword=ceramic prosthesis kn-keyword=ceramic prosthesis en-keyword=zirconia laminates kn-keyword=zirconia laminates en-keyword=stereolithography kn-keyword=stereolithography en-keyword=thermogravimetry–differential thermal analysis kn-keyword=thermogravimetry–differential thermal analysis en-keyword=X-ray diffraction kn-keyword=X-ray diffraction en-keyword=scanning electron microscopy kn-keyword=scanning electron microscopy END