<?xml version="1.0" encoding="Windows-31J"?>
<ArticleSet xmlns="http://www.openarchives.org/OAI/2.0/">
  <Article>
    <Journal>
      <PublisherName>MDPI AG</PublisherName>
      <JournalTitle>Acta Medica Okayama</JournalTitle>
      <Issn>2076-3417</Issn>
      <Volume>15</Volume>
      <Issue>11</Issue>
      <PubDate PubStatus="ppublish">
        <Year>2025</Year>
        <Month/>
      </PubDate>
    </Journal>
    <ArticleTitle>Top-Down Stereolithography-Based System for Additive Manufacturing of Zirconia for Dental Applications</ArticleTitle>
    <FirstPage LZero="delete">6155</FirstPage>
    <LastPage/>
    <Language>EN</Language>
    <AuthorList>
      <Author>
        <FirstName EmptyYN="N">Kumiko</FirstName>
        <LastName>Yoshihara</LastName>
        <Affiliation>National Institute of Advanced Industrial Science and Technology (AIST), Health and Medical Research Institute</Affiliation>
      </Author>
      <Author>
        <FirstName EmptyYN="N">Noriyuki</FirstName>
        <LastName>Nagaoka</LastName>
        <Affiliation>Advanced Research Center for Oral and Craniofacial Sciences, Okayama University Dental School</Affiliation>
      </Author>
      <Author>
        <FirstName EmptyYN="N">Fiona</FirstName>
        <LastName>Spirrett</LastName>
        <Affiliation>Joining and Welding Research Institute, Osaka University</Affiliation>
      </Author>
      <Author>
        <FirstName EmptyYN="N">Yukinori</FirstName>
        <LastName>Maruo</LastName>
        <Affiliation>Department of Prosthodontics, Okayama University</Affiliation>
      </Author>
      <Author>
        <FirstName EmptyYN="N">Yasuhiro</FirstName>
        <LastName>Yoshida</LastName>
        <Affiliation>Department of Biomaterials and Bioengineering, Faculty of Dental Medicine, Hokkaido University</Affiliation>
      </Author>
      <Author>
        <FirstName EmptyYN="N">Bart</FirstName>
        <LastName>Van Meerbeek</LastName>
        <Affiliation>BIOMAT, Department of Oral Health Sciences, KU Leuven</Affiliation>
      </Author>
      <Author>
        <FirstName EmptyYN="N">Soshu</FirstName>
        <LastName>Kirihara</LastName>
        <Affiliation>Joining and Welding Research Institute, Osaka University</Affiliation>
      </Author>
    </AuthorList>
    <PublicationType/>
    <ArticleIdList>
      <ArticleId IdType="doi"/>
    </ArticleIdList>
    <Abstract>This study investigated the feasibility and effectiveness of a commercial top-down stereolithography (SLA)-based system for the additive manufacturing of zirconia dental prostheses. Yttria-stabilized zirconia&#8211;resin slurries were prepared, and zirconia objects were fabricated using a top-down SLA system. Thermogravimetric&#8211;differential thermal analysis was used to examine the resin, while X-ray fluorescence spectroscopy and X-ray diffraction were used to analyze the printed samples. The microstructures of additively manufactured and subtractively manufactured zirconia were compared using field emission scanning electron microscopy (FE-SEM) before and after sintering. Biaxial flexural strength tests were also conducted to evaluate mechanical properties. The green bodies obtained via additive manufacturing exhibited uniform layering with strong interlayer adhesion. After sintering, the structures were dense with minimal porosity. However, compared to subtractively manufactured zirconia, the additively manufactured specimens showed slightly higher porosity and lower biaxial flexural strength. The results demonstrate the potential of SLA-based additive manufacturing for dental zirconia applications while also highlighting its current mechanical limitations. The study also showed that using a blade to evenly spread viscous slurry layers in a top-down SLA system can effectively reduce oxygen inhibition at the surface and relieve internal stresses during the layer-by-layer printing process, offering a promising direction for clinical adaptation.</Abstract>
    <CoiStatement>No potential conflict of interest relevant to this article was reported.</CoiStatement>
    <ObjectList>
      <Object Type="keyword">
        <Param Name="value">additive manufacturing</Param>
      </Object>
      <Object Type="keyword">
        <Param Name="value">subtractive manufacturing</Param>
      </Object>
      <Object Type="keyword">
        <Param Name="value">dental prosthesis</Param>
      </Object>
      <Object Type="keyword">
        <Param Name="value">ceramic prosthesis</Param>
      </Object>
      <Object Type="keyword">
        <Param Name="value">zirconia laminates</Param>
      </Object>
      <Object Type="keyword">
        <Param Name="value">stereolithography</Param>
      </Object>
      <Object Type="keyword">
        <Param Name="value">thermogravimetry&#8211;differential thermal analysis</Param>
      </Object>
      <Object Type="keyword">
        <Param Name="value">X-ray diffraction</Param>
      </Object>
      <Object Type="keyword">
        <Param Name="value">scanning electron microscopy</Param>
      </Object>
    </ObjectList>
    <ReferenceList/>
  </Article>
</ArticleSet>
